RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: drac1
Showing results 1 to 11 of 11
Search took 0.01 seconds.
Forum: RC Pattern Flying
12-21-2019, 10:04 AM
Replies: 45
Views: 12,684
Posted By drac1

There's no provision on the Hyde Mount to use the...

There's no provision on the Hyde Mount to use the YS damper. It's not needed with the Hyde Mount.
Forum: RC Pattern Flying
05-10-2018, 09:50 AM
Replies: 45
Views: 12,684
Posted By drac1

My 185cdi - 30% nitro, is 1.1 bar at idle. I...

My 185cdi - 30% nitro, is 1.1 bar at idle. I haven't checked my 200.

Once the reg is set, I suppose having to keep richening the reg is an indication that the pump is worn.
Forum: RC Pattern Flying
05-10-2018, 07:19 AM
Replies: 45
Views: 12,684
Posted By drac1

Knowing what the actual pressure is, isn't really...

Knowing what the actual pressure is, isn't really necessary. Flying is the only way to set the reg and needle properly. I start with the reg rich and lean it 1/8 a turn at a time until the transition...
Forum: RC Pattern Flying
05-08-2018, 02:09 PM
Replies: 45
Views: 12,684
Posted By drac1

Yes, I am sure!! 14 - 16 kpa is NOT 0.14 -...

Yes, I am sure!!

14 - 16 kpa is NOT 0.14 - 0.16 bar. It is 0.014 - 0.016 bar.

You say 1/4 turn is 0.14 - 0.16 bar, (which is 140 - 160 kpa ). I said 1/8 turn is 70 - 80 kpa, so that's exactly...
Forum: RC Pattern Flying
05-07-2018, 06:59 PM
Replies: 45
Views: 12,684
Posted By drac1

I don't have a zero, but on my 185cdi 1/8th turn...

I don't have a zero, but on my 185cdi 1/8th turn on the reg is around 70 - 80 kpa difference in pressure.
Forum: RC Pattern Flying
02-01-2018, 01:37 AM
Replies: 45
Views: 12,684
Posted By drac1

It would be worth trying YS fuel tube.

It would be worth trying YS fuel tube.
Forum: RC Pattern Flying
01-31-2018, 12:46 AM
Replies: 45
Views: 12,684
Posted By drac1

Was it the pump to carb line or carb to injector...

Was it the pump to carb line or carb to injector line that was splitting?
Forum: RC Pattern Flying
01-30-2018, 01:21 PM
Replies: 45
Views: 12,684
Posted By drac1

For the 185 Red and 200, the manual specifies...

For the 185 Red and 200, the manual specifies that the carb to injector line, (tube C), must be a soft tube with 3mm ID and 5mm OD. This is to do with the new injector not having the check valve on...
Forum: RC Pattern Flying
01-29-2018, 09:13 PM
Replies: 45
Views: 12,684
Posted By drac1

In regards to fuel tubing, I'm not convinced that...

In regards to fuel tubing, I'm not convinced that is a issue. I've used YS tube, Dubro medium tube and now Prather medium which I've been using for a few years now. Haven't had problems with any of...
Forum: RC Pattern Flying
01-29-2018, 09:09 PM
Replies: 45
Views: 12,684
Posted By drac1

Hi Arnstein, I have used the Hyde LR85...

Hi Arnstein,

I have used the Hyde LR85 mount, (no damper), as well as the YS Super mount. I didn't notice any difference in idling or transition between the two, but I do think the Super mount is...
Forum: RC Pattern Flying
01-28-2018, 11:52 PM
Replies: 45
Views: 12,684
Posted By drac1

Hi Arnstein, The Zero has higher compression...

Hi Arnstein,

The Zero has higher compression to compensate for no nitro, so I would expect the idle to be a bit higher.

What mount were you originally using?

Scott
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.